WSJT-X Improved by Uwe Risse, DG2YCB offers the ability to play sounds for certain criteria, such as hearing a new DXCC, new grid, new continent etc.
Download WSJT-X Improved: https://sourceforge.net/projects/wsjt-x-improved/
My two favorites are alerting me to a new DXCC … Read more...
An Alinco DR-735T was purchased recently, and so came the need to program it via the freely available Alinco Clone Utility software.
I wasn’t about to pay $69 for a simple programming lead, and found this schematic floating around … Read more...
Shipping has resumed to the USA as of 14/10/2025.
(That’s 14th October, 2025 for y’all)
With Trumps Executive Order 14324, a 10% tariff is now applicable to shipments to the USA.
Zonos are acting as the tariff collection 3rd … Read more...
The OEM incandescent lamp in a Daiwa SWR & Power meter which failed is being replaced with modern LEDs.
Five Philips heads screws, 2 on each side and one at the top are removed, and the meter’s top cover is … Read more...
It doesn’t get any simpler than this!
This interface uses the RTS and DTR signal lines from a cheap FTDI USB Serial Adapter, and provides isolated keying for both PTT and a CW key.
Problem!
The FTDI adapter provides … Read more...
Adam fixes his faulty 40M Off Center Fed dipole, after being exposed to the elements for 16 years.
The enclosure was cracked, no doubt caused by the SO-239 being recessed into the sidewall.
A thinner sidewall means the connector will … Read more...
Both the Eltek Flatpack2 Touchscreen Controller and Eltek Monitor projects have been updated.
The PCB has been redesigned so the controller board can now piggyback mount to the screen.
This makes mounting much easier, with only one set of screws … Read more...
The following Eltek Flatpack 2 Rectifiers are known to work with all of my Eltek controllers.
Thank you to those who spent a few minutes to take a photo and send it in.
• Flatpack2 48/2000 HE 24115.105 … Read more...
Two versions of the Eltek Flatpack 2 Monitor are now available, one with a colour TFT screen, and the other with a mono OLED screen.
The colour screen has one fixed font.
A close up pictures shows the large text … Read more...
Update: 19-Dec-2023
Eltek FP2 Monitor is currently being developed as a replacement for the popular Volts Setter.
Eltek Monitor is used to set the default start-up voltage of an Eltek FLATPACK2 24 V or 48 V Rectifier, and the following … Read more...
In the Tokyo burbs, Akihabara, also known as “Electric Town”, is heaven for ham radio shopping.
This district is also a Mecca for all sorts of electronics, PCs and gadgets, and attracts tourist from all over.
Make sure you have … Read more...
For working satellites, horizontally polarised yagi antennas will be mounted on a non-conductive crossboom made of FRP (Fibreglass Reinforced Polymer).
A Yaesu G-800DXA azimuth rotator is already on station, so only a system to rotate elevation is required.
Elevation rotation … Read more...
VK Reference Code plug for Anytone AT-D878UVII+ (v3.01 firmware) hand held radio.
Features
• Mode 0 (zero)
• Most known VK DMR repeaters – considering the poor state of VKDMR.com, and the foolish decision to use a Stupidbook … Read more...
Another batch of Eltek Volts Setters have been assembled and tested.
This batch features a blue OLED display.
(Previous batches had a white OLED)
Now available in the VK4GHZ store.
Price remains the same.
… Read more...
VK Reference Code plug for Anytone AT-D878UVII+ (v2.05 firmware) hand held radio.
Features
• Mode 0 (zero)
• All current VK DMR repeaters
• Channels – All Digital repeater channels have callsign & TS & TG in name… Read more...
Copyright © 2025 | WordPress Theme by MH Themes