What's on your Workbench?
Re: What's on your Workbench?
Do you have any internal photos Ian?
Re: What's on your Workbench?
I received a V2 Agile PLL from Graham today.
It is not committed to a particular application, but rather an experimental device with some initial projects lined up. For that reason, I will use a different controller and provide facility to update firmware and configuration from outside the box. I intend trying Graham's amplitude keying solution, and also the Si4133's capacity to turn an oscillator on and off, and of course FSK... but frequency shift is not very flexible for this type of PLL.
One experiment may be a 20W GPS locked beacon on 2m using QRSS3 keying. The real maybe about this is that experience shows that QRSS does not attract observer reports.
I am now waiting on some parts on a slow boat from China (eg some SMA/RG316 tails to plumb the outputs to the back of the diecast box).
A WIP.
Owen
It is not committed to a particular application, but rather an experimental device with some initial projects lined up. For that reason, I will use a different controller and provide facility to update firmware and configuration from outside the box. I intend trying Graham's amplitude keying solution, and also the Si4133's capacity to turn an oscillator on and off, and of course FSK... but frequency shift is not very flexible for this type of PLL.
One experiment may be a 20W GPS locked beacon on 2m using QRSS3 keying. The real maybe about this is that experience shows that QRSS does not attract observer reports.
I am now waiting on some parts on a slow boat from China (eg some SMA/RG316 tails to plumb the outputs to the back of the diecast box).
A WIP.
Owen
Re: What's on your Workbench?
Owen
Re: What's on your Workbench?
I'm working on putting a 23cm transverter/amp into a 19 inch 2U rack case. Along with the sequencer and switching relays, 28v SMPS, bi-directional coupler and the 28v to 12v converter (not shown in pic) it's going to be a bit tight. Figuring out the most efficient layout is interesting! It looks relatively bare at the moment, but it'll be very different once I start laying the semi rigid coax and wiring up the sequencer.
Does anyone have a contact that does etching/drilling of front panels?
Does anyone have a contact that does etching/drilling of front panels?
Re: What's on your Workbench?
There's these people - you download their CAD program, design your panel, then the software will quote for it and you can submit the order and get it cut in whatever colours or finish you fancy. Not cheap though!
http://www.frontpanelexpress.com/
73 - Rob VK2GOM / GW0MOH
http://www.frontpanelexpress.com/
73 - Rob VK2GOM / GW0MOH
- VK2JDS
- Forum Diehard
- Posts: 432
- Joined: Wed Feb 15, 2006 8:17 am
- Location: qf46pv nsw central tablelands
- Contact:
Re: What's on your Workbench?
I just finished building up a vfo kit based on the si570 chip.
It is a standalone device (no usb or pc reqd) and operates in 1Hz steps from 3.45MHz to 940MHz (or higher depending on what flavour of si570 your have)
I already had a si570 so i bought the "PA0KLT Kit D Low Noise Synthesized VFO Kit - Si570 Chip NOT supplied" for 22 pounds plus about 5 pounds postage.
Its a absolute bargain and works as well as they claim. It took me today (raining/sleet etc) to assemble, test and fit-out the device into a box with a couple of 18650 lithiums in a holder inside.
I calibrated it (chip cal is built into the software) against WWV for zero beat and its very stable.
Now I can dial up a frequency and use this as a sig-gen, weak signal source or a LO and the harmonics will be useful up into the microwave regions.
If you have an old transciever with a drifting analogue vfo then this unit is a drop-in vfo replacement and its got RIT, 32 memories, 2 vfo's, programmable IF offset to suit any radio, offsets for each mode CW,LSB,USB etc etc and simple to build!
Have a look at it here : http://sdr-kits.net/PA0KLT_Description.html
I built mine into a 4 inch by 4 inch by 2 inch high electrical IP56 box so its rugged and battery powered, with a bnc socket so it can take a whip antenna etc (was going to use sma but no single-hole ones in the junque box). It just needs some stick-on labels for the pressbuttons and its finished.
73 Dave vk2jds
It is a standalone device (no usb or pc reqd) and operates in 1Hz steps from 3.45MHz to 940MHz (or higher depending on what flavour of si570 your have)
I already had a si570 so i bought the "PA0KLT Kit D Low Noise Synthesized VFO Kit - Si570 Chip NOT supplied" for 22 pounds plus about 5 pounds postage.
Its a absolute bargain and works as well as they claim. It took me today (raining/sleet etc) to assemble, test and fit-out the device into a box with a couple of 18650 lithiums in a holder inside.
I calibrated it (chip cal is built into the software) against WWV for zero beat and its very stable.
Now I can dial up a frequency and use this as a sig-gen, weak signal source or a LO and the harmonics will be useful up into the microwave regions.
If you have an old transciever with a drifting analogue vfo then this unit is a drop-in vfo replacement and its got RIT, 32 memories, 2 vfo's, programmable IF offset to suit any radio, offsets for each mode CW,LSB,USB etc etc and simple to build!
Have a look at it here : http://sdr-kits.net/PA0KLT_Description.html
I built mine into a 4 inch by 4 inch by 2 inch high electrical IP56 box so its rugged and battery powered, with a bnc socket so it can take a whip antenna etc (was going to use sma but no single-hole ones in the junque box). It just needs some stick-on labels for the pressbuttons and its finished.
73 Dave vk2jds
Re: What's on your Workbench?
Must have been the day to stay inside and solder?
Here's a portable 10MHz reference based on the G3RUH design. It uses a Jupiter T GPS engine that has a 10kHz output as well as the 1PPS. The 10MHz is divided down to 10KHz and compared against the GPS signal. The error voltage is used to control the OCXO. The 10MHz output looks roughly sinusoidal but it's rich in harmonics so best to use some kind of filter at the output. The Demi 4 way 10MHz splitter cleans it right up.
It takes just over 10 minutes to stabilize. The case is 170x120x60mm. It works out about half the cost of a Trimble Thunderbolt.
Details as requested. http://www.jrmiller.demon.co.uk/project ... rqstd0.htm
Here's a portable 10MHz reference based on the G3RUH design. It uses a Jupiter T GPS engine that has a 10kHz output as well as the 1PPS. The 10MHz is divided down to 10KHz and compared against the GPS signal. The error voltage is used to control the OCXO. The 10MHz output looks roughly sinusoidal but it's rich in harmonics so best to use some kind of filter at the output. The Demi 4 way 10MHz splitter cleans it right up.
It takes just over 10 minutes to stabilize. The case is 170x120x60mm. It works out about half the cost of a Trimble Thunderbolt.
Details as requested. http://www.jrmiller.demon.co.uk/project ... rqstd0.htm
Last edited by VK3ALB on Sun Jun 29, 2014 9:44 pm, edited 1 time in total.
Lou - VK3ALB
Being right doesn't excuse bad behaviour
Being right doesn't excuse bad behaviour
Re: What's on your Workbench?
A very neat solution, Lou. And cost-effective to boot!
73, Roger Harrison VK2ZRH
Re: What's on your Workbench?
Started building a DSB rig for 40m
Re: What's on your Workbench?
A little test of VK3XDK's Agile PLL V2 in A1 CW using a keyer to key one address line to select between normal programming of the IF VCO and VCO OFF.
Note, this is not the MOSFET keyer of the MMICs on board... in fact this board doesn't (yet) have MMICs on it.
Negligible clicks, this would be suitable to put to air (keying wise).
Note, this is not the original controller chip.
Owen
Note, this is not the MOSFET keyer of the MMICs on board... in fact this board doesn't (yet) have MMICs on it.
Negligible clicks, this would be suitable to put to air (keying wise).
Note, this is not the original controller chip.
Owen
Re: What's on your Workbench?
Above is the burst of clock pulses during 4 x 3 byte transfers to the Si4133 for ordering up the carrier. The OFF set is shorter (just one register). At just over 100µs, it sustains keying at beacon speeds just fine.VK2OMD wrote:...
Note, this is not the original controller chip.
The PLL itself in stunningly fast, faster than I write the data to it, it actually relocks between the write of the R divider register and the N divider register.
Owen
Edit: The original controller takes around 700ms for a data transfer, so it is unsuited to normal CW speed keying.
- VK3BQ
- Forum Diehard
- Posts: 617
- Joined: Wed Sep 02, 2009 9:13 pm
- Location: Mt Waverley, Vic.
- Contact:
What's on your Workbench?
While I don't have the construction skills (yet) of a lot of you. I've been increasing my building of small items to help solve that. This is a band pass filter for 10mhz to turn my raspberry pi into a wspr beacon.
Re: What's on your Workbench?
Since you didn't ask , I would spend a bit more time getting the insulation off those wires and some of that tinning looks like the iron may have been used to paint the solder on. If there's enough heat on a clean wire the solder should flow really nicely and the result will be clean and bright. It's a real bugger getting the insulation off if it doesn't burn away with the application of heat. I like using the blade of a hobby knife to scrape away the insulation. The toughest part is that the wires are so small and you have to work in close. I think Adam posted some info regarding holding cores in a soft jaw vice.VK3BQ wrote:While I don't have the construction skills (yet) of a lot of you. I've been increasing my building of small items to help solve that.
Posted in the spirit of sharing and assistance.
Lou - VK3ALB
Being right doesn't excuse bad behaviour
Being right doesn't excuse bad behaviour
- VK3HZ
- Forum Diehard
- Posts: 436
- Joined: Sat Apr 02, 2005 4:52 pm
- Location: Melbourne, Australia
- Contact:
Re: What's on your Workbench?
Hi Owen,VK2OMD wrote:A little test of VK3XDK's Agile PLL V2 in A1 CW using a keyer to key one address line to select between normal programming of the IF VCO and VCO OFF.
Note, this is not the MOSFET keyer of the MMICs on board... in fact this board doesn't (yet) have MMICs on it.
Negligible clicks, this would be suitable to put to air (keying wise).
Owen
You'll find that on some frequencies, the VCO comes on very rapidly and clicks badly - been there, done that, hence the addition of the external MOSFET switching for the MMICs.
BTW, if anyone wants to use the PLL board as a locked beacon source, there is already beacon code available for the original PICAXE controller.
Regards,
Dave
VK3HZ
Re: What's on your Workbench?
Thanks David, I will keep that in mind. The project is awaiting some bits from China to finish boxing it up, and when I have done that I will try CW on 70cm.VK3HZ wrote:...
You'll find that on some frequencies, the VCO comes on very rapidly and clicks badly - been there, done that, hence the addition of the external MOSFET switching for the MMICs.
Owen
Re: What's on your Workbench?
A solder pot is the best thing i ever brought for tinning wires. $15 from eBay. The solder I put in in costed more.
- VK3BQ
- Forum Diehard
- Posts: 617
- Joined: Wed Sep 02, 2009 9:13 pm
- Location: Mt Waverley, Vic.
- Contact:
What's on your Workbench?
They are installed now. I had another go at the legs after that photo. They seemed to have a pretty good cover. I spent some time with the side cutters scrapping. The wire is 3 layers of epoxy. A pain to get rid of. But thanks again for the pointers. Learning. Ps. I used the instructions from the supplier website. http://www.kitsandparts.com/univbpfilter.php. And made sure I cleaned it as best I could.
Last edited by VK3BQ on Thu Jul 03, 2014 4:05 pm, edited 1 time in total.
Re: What's on your Workbench?
For next time...VK3BQ wrote:They are installed now. I had another go at the legs after that photo. They seemed to have a pretty good cover. I spent some time with the side cutters scrapping. The wire is 3 layers of epoxy. A pain to get rid of. But thanks again for the pointers. Learning.
Enamels fall into two broad classes, those that 'melt' when heated to soldering temperatures and those that don't.
In the first case, you try to tin them with solder and a very hot iron, and the enamel will bubble up and the wires tin. (Don't try this now that it is in the PCB, you will probably damage the PCB.
In the last case, you must clean the enamel off with a blade, sandpaper etc prior to soldering... it is very difficult to fix them after you have applied solder. You can try degrading the enamel with a cigarette lighter, but you will still have to scrape some residue off to get clean copper which will accept solder.
Owen
Last edited by VK2OMD on Thu Jul 03, 2014 5:10 pm, edited 1 time in total.
Re: What's on your Workbench?
You can check your coils have good continuity by checking with a multimeter from pad to pad on the PCB - not lead to lead. You must test pad to pad to determine continuity to test the integrity of the solder to enamelled wire joint. Of course assuming no solder bridges
And then the fun will begin with a spectrum analyser with a tracking generator to get the thing into bandpass spec. It should be possible to design and build a BPF these days with decent quality spec fixed value components and not have to resort to supplying variable trimmer caps!
73 - Rob VK2GOM / GW0MOH
And then the fun will begin with a spectrum analyser with a tracking generator to get the thing into bandpass spec. It should be possible to design and build a BPF these days with decent quality spec fixed value components and not have to resort to supplying variable trimmer caps!
73 - Rob VK2GOM / GW0MOH
Re: What's on your Workbench?
But..but..but......It should be possible to design and build a BPF these days with decent quality spec fixed value components and not have to resort to supplying variable trimmer caps!
That doesn't leave anything for the fiddlers to twiddle.