VK Logger Ham Radio Forum Archive

2nd request
source of other than icom
for flat grey coloured 25 conductor lead that connects the ux910 to jack two on rhs of main rx board?

pitch is 0.8 mm leaving 0.2 mm gap between 25 conductors with tinned ends total edge to edge is 25 mm?

tinned for direct plug in.

looking for a replacement flat cable as used to direct plug into Jack two rh end for the icom ux910 1286 module mine have peeled back. Inam told china is cheap icom is $18; no supply date. what name do they go by? where to buy? mine is 25 mm total width 25 flat grey tinned conductors printed onto fl...

As used in ux910 1296 module plugging into Jack 2 tinned ends grey flat.

expensive from icom

Thanks Adam,
A good logger is the old logger
now to put on my 2x glasses

I now have same issue
can someone please tell me the part number and circuit number so I can order from ICOM thanks

ZAZ

Garry confirming good decodes from you on 144.4905 close to VK5GF in drift. My 432 drift is my problem on my ocxo 910. Good job. The gpsdo from ebay is sufficient, paying any more is buying much the same thing. Next is to extract the nmea word to lock and eliminate the lead to the 9700 clock/gps dst...

I have been turning shack off at night due to plethora of plug packs running for tnc gps laptop lan, hand helds, etc. Not wishing a shack burn down as many houses are lost to crappy plug packs and ham radio plug packs are no exception. So in morning you must turn on gpsdo ages before your 9700 and e...

ok polly you can help me terminate the ldf and my recently acquired atn 27 element lpyagi designed by klm and cloned all over vk. Now there is a story in itself. ps my ic910a complete with 144-146 no repeater offset came off a stall at Tokyo ham fair for ¥240000 including an icom carry bag and a hat.

This part is interesting 'A small coupler PC board is soldered to the top of the TCXO can inside the IC-9700'. Any residual solder evidence from this 'mod' will no doubt void the warranty. The first few returns to Icom might slip through as warranty jobs, but I'm sure they will be on the look out f...

https://www.icom.co.jp/world/support/download/firm/IC-9700/CS-9700_1_10/ Firmware update purports to auto sync with your GPSDO reference source. I updated and my radio changed by 5 hz. Watching the Sync ref it has now dropped from 33% fine to 32% fine as it warmed upforwantof a better word. GPS lock...

All gone a tad quiet on this discussion. RT systems now have rig programmer using standard usb for $35 us. it allows cut and paste from any other rt systems radio so you can cut and paste all the 2m freqs fwiw. Icom have a freebie but not as flexible. no further upgrades. notice a few of the wspr us...

VK5PJ
If you remember wannin tower
2.5 inch Thai steel seamless
21 feet.
rotor at 90 feet.
Ten feet inside to the thrust bearing on top
twelve feet out.
top was 111 feet agl
supported a five el ten metre beam at top.
nine el six m forty footer at thrust at 100 feet.
never failed.

Thanks to Tim vk3rpg-2 is back on 145.175 and gateway via vk3mix horsham this morning it tracked accurately from hamilton to port melbourne and return for sux hours and as my wife pointed out freeway 110 dear, highways and c class roads are 100! Stalked and sprung like a blooming idiot. My excuse ju...

three sections for sale.
nothing is welded
all clamps and bolts.
see vk classies

Hi all,
need big favour in return for some fuel money.
Anyone who could transport some aerials from mid north sa to serg please pm me.
A collapsed lpy and two metre yagis from vk5mas peterborough sa.

1993 6M CW eme
never repeated on CW from VK
25 years ago massive improvement in radios and antenna.
World record up for grabs if you work W6JKV in Austin TX.

QED
Don't weld two poles together making unmanageable 6M 200kg pole
Flang and fillet weld each end lath cut.
6 x M21 HS bolts
2M section in ground becomes the foundation.
1M hole plus mesh.
Well over rating required.
when you leave pole in ground with pot plant on it.
Pics coming.

Hi all, Would you like to share any pics or diagrams of how you did not mount your Nally on the 3 metre round pole sticking out of the ground. Having trouble accessing site with a hydraulic Auger. Hit clay at 1 metre and had to rescue auger with engine crane just. Thinking of other was. Hinge at bas...

VK3RX wrote:Happy Half-Century, Steve

Well done, that man.

Miss our chats about 6M DX on 125.8 in the morning commute to MB

VK6OX wrote:Well done Steve!
A certain "Rick" from Hamilton was on ABC's Macca program this morning....d'you happen to know him?

Yeah felt bit like a Dick!